You have no items in your shopping cart.

More Views

DTE-3137 | Standalone

DVB-S2 satellite receiver is DekTec's standalone power-over-ethernet enabled DVB-S2 Satellite Receiver, allowing reception of the full Transport Stream and transmit it to IP and ASI networks. Networked DVB-S2 receiver includes PoE DTE-PWR2.

Ordering Information

  • DTE-3137 - Networked DVB-S(2) receiver

Netto weigth: 358 gr

Availability: In stock

1 399,-€
1 399,-€




  • Standalone DVB-S2 receiver supporting QPSK, 8PSK, 16APSK and 32APSK
  • DVB-S2 demodulation compliant to EN302-307 and EN301-210, as well as legacy DVB-S support
  • Web and SNMP interface for setting parameters and observing status
  • Unit can be powered via the Ethernet cable (Power over Ethernet) or through a DC power supply jack
  • LNB power insertion
  • Full support of SMPTE 2022-1/2, with 2D FEC encoder for robust transport over IP
  • LCD status display shows device identifier, mode, carrier frequency, level, SNR, BER and IP/MAC address
  • Install up to 12 modules in 3U 19” rack space using DekTec rack-mountable rail


  • General-purpose receiver for obtaining the full Transport Stream from a DVB-S/S2 signal
  • SMATV: Redistribution of satellite TV
  • Portable demo set
  • On-site recording and analysis of DVB-S/S2 streams

Key Characteristics

Control Webinterface
Standards DVB-S
DVB-S2 modes QPSK
16/32-APSK (CCM only)
Tuning range 950 .. 2150MHz
Bitrate Up to 108Mbps
Sensitivity -30 .. -60dBm
LNB supply 13V/18V (0/22kHz)
IP encapsulation IPv4
RTP (SMPTE 2022-2)
FEC SMPTE 2022-1
ASI specifications DVB-ASI (coax) EN50083-9

Inputs and outputs

Ethernet connector RJ-45
1x RF in 75-Ω F-type
1x ASI out 75-Ω BNC

PC Requirements

OS Windows XP, 2k3/2k8, Vista, 7, 8/8.1, 10 Linux  ≥2.6.18, 3.x, 4.x


  • DTE-3137 Leaflet       
  • DTE-3137 Test Report       
  • DTE-MIB (General MIB for DTEs)   
  • DTE-S2-RX-MIB DVB-S2 receiver MIB   


  • DTE-3137 firmware   

Dektec models are most often differentiated by the sufix e.g. SD, SXP etc., where suffix specifies the SW licence
  • SP = Stream Player (allows you to play/modulate transport stream files, so this makes sence for devices with Output interface)
  • SXP = Stream Xpert (this is MPEG TS ANALYZER, what makes sence for Input devices)
  • SLP = Stream Xper Lite (very limited alternative of SXP, de facto allowing mainly capturing MPEG TS, again makes sence for Input devices)
  • RX = RFXpert RF signal analysys
  • SY = SD Eye (video analyzer)
  • J = Jitter
  • DGL = Dongle license for non Dektec devices
Meaning of abreviations used in beginning of Dektec model names
  • DTA = Dektec adapter (typically PCI, PCI-e)
  • DTU = Dektec USB device both USB-2 and USB-3
  • DTE = Dektec Ethernet standalone networked device
  • DTC = Dektec software license



Manufacturer DekTec
Form Factor Standalone


Write Your Own Review

You're reviewing: DTE-3137 | Standalone

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.